AustinScissor hydraulic elevatorPrice is bullish

The concept of hydraulic boarding bridge The boarding bridge uses the power system. The large oil cylinder raises the entire equipment inclined plate. When it rises to the large height， the small oil cylinder starts to work and stretches out the loose-leaf tongue. All the equipment plates are effectively welded with high quality checkered steel plates and profiles， with long service life.

7For this reason， many mobile elevators will be equipped with various protective equipment to ensure the safety of peoples lives. Now lets see what safety tools are on the mobile elevator?

tAustinReset the brake; Install the service section. The maintenance section is generally installed in Section IV.

The contact surface of each departments brush shall be kept clean， and the brush pressure shall be adjusted to make the contact area not less than %

FNavabganjThe elevator is a common transmission equipment， restaurants and restaurants on the second and third floors. The low height is especially suitable for the workplaces where the pit cannot be excavated and there is no need for the upper lifting point. The form is diversified (single column，Hydraulic lift double column，Wu'anScissor fork mobile elevatorWhat are the specific characteristics of the four column). So what should we do if the speed of the guideway elevator slows down in application?

XcRegularly add lubricating oil to maintain the lift: during the use of the lift， the friction between various components is also relatively large due to the heavy load， especially the lift chain and the lift pivot pin. It is necessary to ensure that the appropriate amount of lubricating oil is added before each use to ensure that the operation is flexible and not blocked. If the elevator is running， especially the bearings should be added with grease regularly. If the grease is not enough， the bearing will be seriously worn during operation， affecting the service life of the machine. There are all kinds of wires and cables in the machine. After a period of use， it is necessary to check the wires and cables. If the wires and cables are damaged， they should be repaired or replaced. We should also regularly check whether the screws at the connection are loose. If the screws are loose， we should tighten them. Some screws must meet certain torque requirements. In the absence of relevant professional equipment，Hydraulic lift we can go to the maintenance shop to use professional equipment to tighten the screws. We must make the screws meet the corresponding torque requirements.

In todays society，“ Brand” It is an intangible asset. As long as a product has a brand， it will have a certain popularity， cohesion and diffusion.

wThe lubrication and hydraulic oil of reducer， gearbox， external gear and other parts shall be carried out according to the requirements in the lubrication table.

TTalking about the daily maintenance and use of the motor of the hydraulic lifting platform. Overload is strictly prohibited. Overload will increase the burden of the motor and cause the motor to burn out in serious cases.

LInstallation conditionsThe reason for the slow rise and fall rate of the aluminum alloy lifting platform and the disposal of the equipment and equipment after the purchase and utilization， due to the improper use or aging， and the use of the hydraulic lift to incubate the dirt， the sign of the slow rate occurred. After the speed slows down， consider the hydraulic oil flow first. The factors affecting the hydraulic oil flow include: hydraulic pipeline，Hydraulic lift hydraulic oil pump， motor speed regulation assembly etc. The following is a brief introduction to the four reasons for the slow speed and the mediation methods.

eKWhat should we pay attention to when starting a new mobile elevator?

The production size of the support rod of the hydraulic lifting platform is inconsistent，Wu'anScissor fork mobile elevatorWhat are the specific characteristics of the which belongs to the quality defect of the lifting platform equipment itself. It is recommended to contact the manufacturer for replacement， which has a low probability.

The water cooling of the hydraulic station is generally tubular water cooling. Its type selection is based on the heat load to calculate the heat exchange area while its air-cooled elevator is based on the air cooler， and the heat exchange capacity is calculated based on the heat load， and then the type selection is calculated under the condition that the flow can be satisfied. Therefore， the two kinds of cooling are different and have great differences.

Installation worksyWhat kinds of elevators are there? There are many types of such equipment， for example， they can be divided into fixed lifting devices and vehicle-mounted lifting devices according to the form of movement. The so-called fixed lifting is generally fixed at one place， and then the lifting operation can be carried out. This type of lifting equipment is usually used more on the assembly line. Some large production lines need to lift the material to a certain position when loading the material，Lift_ Hydraulic elevator_ Hydraulic lift_ Hydraulic lifting platform - lift manufacturer and then put it on the production line for production so a special lifting device needs to be fixed at a certain position on the production line.

FWhen using mobile elevator to carry out work at height， it is required to comply with the safety requirements and specifications of the project site. It is strictly prohibited to use equipment in violation of rules and regulations. During industrial control operation， pay attention to the use of the following safety protection: before using the safety helmet， check whether the safety helmet shell， cap lining and cap belt are complete， safe and effective.

For lifting platforms in some sites， protective barriers are generally added on the platform. Since the lifting platform is a special equipment， the National Quality Inspection Bureau is very strict with this inspection. As long as it is considered that there are potential safety hazards， the lifting platform should be removed. So when the salesperson asks you whether to add guardrails， do not blindly refuse， and consider whether it is necessary according to the site of use. In addition， the production， installation and maintenance can only be carried out with two kinds of certificates， namely， the Special Equipment Manufacturing License of the Peoples Republic of China and the Special Equipment Installation， when purchasing， the manufacturer should ask whether they have these two kinds of certificates.

xAustinAfter careful inspection， it was found that it was mainly caused by two reasons: the loss of hydraulic pressure and the leakage of hydraulic valve or seal.

yJThe elevator is a common transmission equipment， and the types selected in different fields are different. The guideway elevator is a kind that we all know. It is mainly used for the goods transmission between the floors of industrial buildings， restaurants and restaurants on the second and third floors. The low height is especially suitable for the workplaces where the pit cannot be excavated， and there is no need for the upper lifting point. The form is diversified (single column， double column， four column). So what should we do if the speed of the guideway elevator slows down in application?

This fixed lifting equipment can also be used in the warehouse. For example， a certain floor in the warehouse needs to be lifted to send goods or personnel to the designated warehouse location.In addition to the fixed mode， there is also the type of vehicle-mounted mobile. As the name implies， it is a combination of lifting equipment and vehicle-mounted system. Such a lifting equipment is very flexible to move， and of course it is better to use. For example， there is such a lifting equipment in the airport， and the station or stadium may also place such equipment， because it can be moved， Then the scope of operation is not limited to a certain place， but can be used wherever lifting operation is required. For example， when installing outdoor advertisements， some advertisements are relatively high. At this time， mobile lifting equipment can be used to send billboards or staff to the designated height for work. This kind of equipment can also be divided into hydraulic lifting and electric lifting according to the driving mode. The so-called hydraulic lifting is to use hydraulic oil to drive to reach the specified height. The electric mode is to lift to a certain height through motor driving or tooth movement. However， the hydraulic lifting platform is more widely used at present.