NangongScissor fork high-altitude elevatorThe important role in the game, its magic is here

The oil condition of each system of the elevator shall be checked， and the oil shall be replaced in time in case of foaming and turbidity.

6The lifting platform shall be placed in a trench position， and the corresponding anti-slip work shall be done; Remove the gear box of the equipment， remove the axle oil box， and take out the lower bearing and oil suction device; Slowly test run and check whether the surface around the axle diameter is seriously damaged; If the damage is serious and tungsten is occupied polish it with oilstone; Under the motor， and with the sleeper on the trench edge inside the rail，Elevator manufacturer use the jack to periodically pull the motor and remove the upper tile; How to solve the damage of the important equipment in the lifting platform? Check the status of the bearing pads and oil absorbers，OrdosPlant LiftWhat are the basic requirements for manufacturing investigate the cause of the damage， and clean the bearing oil box; After assembling all parts and components， install a new oil suction device on the axle oil box and inject clean axle oil; The gear box shall be filled with gear lubricating oil as required; Burn of axle box bearing is the most common one， which is the outer row bearing. If it is serious， the axle box and wheel set will be fixed together， affecting the equipment operation.

aNangongIt is forbidden to combine two layers of top liner of safety helmet into one layer.

The starting system of the manual hydraulic stacking platform car is divided into pedal type and manual control type， which is simple and easy to operate. The model is divided into fixed and mobile forkThere are many options for legs. It is very suitable for the placement and extraction of goods in warehouses and supermarkets.

TAntibesMobile elevators are generally used in skyscrapers where electric elevators are used， because there is no need to stop in the middle of the way， so fast elevators are needed. First go to the Skylobby on the ground，Elevator manufacturer then transfer to the ordinary elevator to the destination. Some new elevators use the elevator pre-call system， which can pre-call the designated floors in the lobby. These passenger lifts can be beautifully decorated according to customers needs. Some passenger lifts will also be equipped with air conditioners and televisions， and some car settings are transparent， so that customers can enjoy the scenery outside while riding.

XsHow do lift manufacturers maintain and maintain construction lifts? In order to accurately implement the equipment maintenance system， a mechanical management responsibility system must be established; Maintenance procedures for different models must be formulated; The corresponding maintenance organization must be implemented; The relationship between maintenance and production must be properly handled to ensure that it does not affect production and equipment maintenance.

Usually check whether the organizations operate normally and whether there is any noise. If any obstacle is found， it must be removed immediately.

How to properly handle the elevator after water ingress to keep the elevator high in front and low in back as far as possible， which is beneficial to discharge the water entering the exhaust pipe and avoid damage to the converter.

qThe oil filter is seriously blocked; The solution is to clean the oil filter or replace the hydraulic oil.

HThe guide mechanism of the guide mechanism of the guide rail elevator manufacturer is mainly composed of the guide plastic tube， the guide bracket， the compression spring， the safety plug，Elevator manufacturer the guide housing， the guide shaft and other parts. As a semi-sectional view of the guide mechanism a narrow gap is formed between the two guide plastic tubes，OrdosPlant LiftWhat are the basic requirements for manufacturing and the lifting cloth belt extends out of the box from the narrow gap to prevent the cloth belt from being tangled and play a guiding role. The safety plug is supported by a guide bracket and a compression spring. In order to prevent the compression spring from losing stability after being stressed a small guide rod is designed on the safety plug. The clearance between the small guide rod and the spring is designed according to the table. The lifting arm shaft is welded， and a lifting arm hook is installed at both ends. The material is selected， and the material is quenched and tempered. Together with the hook at the lower shell of the box， the distance between the two lifting arm hooks is listed in the table as the design reference， The balance bar is used to maintain the balance of the lifting device. The material is designed to be hollow tubular， which reduces the overall weight of the lifting arm.

CCustomer firstWhen using， the four legs should be firmly supported on the solid ground (subject to the fact that the walking wheel is about to leave the ground). Sleepers can be used when necessary.

oYBefore using the machine， the staff should carefully check the hydraulic and electrical systems，Lift_ Hydraulic elevator_ Hydraulic lift_ Hydraulic lifting platform - lift manufacturer and use it only after there is no leakage or bare leakage.

The solenoid valve on the motor should not be adjusted at will. The solenoid valve is pre-adjusted before leaving the factory. After being adjusted at will， and the service life of the motor will be shortened in serious cases.

Avoid humidity， especially during storage. Store in a cool and dry place， and avoid rain and snow during work.

Meticulous workmanshipaThe maintenance shall be carried out in accordance with the Special Equipment Supervision Regulations， the Elevator Supervision and Inspection Regulations， the Elevator Maintenance Rules (GB) and relevant national， industrial and local standards.

UThe technical parameters and uses of each type are slightly different， as a customer， you should have a purposeful choice， that is， what you want to do when you buy a lifting machine， and which lifting machine can meet your needs and use many purposes.

How to prolong the service life of hydraulic lifting platform? In order to prolong the service life of such machinery and equipment， it is necessary to regularly repair and maintain the equipment during normal use. For example， there are various switch devices in the machinery and equipment. During use， it is necessary to regularly check whether these switches can be used normally and whether the contact points of the switches are good. There will be an electric box and distribution box inside the elevator. Dust is easy to accumulate outside these equipment. If too much dust is accumulated， it may cause corrosion outside the electric box. Therefore， the dust outside the various boxes should be removed regularly during use. Generally this work is what operators should do after each operation.

jNangongRegularly add lubricating oil to maintain the lift: during the use of the lift， the friction between various components is also relatively large due to the heavy load， especially the lift chain and the lift pivot pin. It is necessary to ensure that the appropriate amount of lubricating oil is added before each use to ensure that the operation is flexible and not blocked. If the elevator is running， once“ appears; Squeak” It can be basically concluded that the friction noise is due to the lack of lubricating oil in the elevator. It is necessary to stop working immediately and find out the reason. It is easy to cause unpredictable hidden dangers. Point summary: it is not allowed to add lubricating oil regularly to maintain the elevator.

wJThe detailed reason why the hydraulic station cannot be washed with water is that if it is done， it will corrode the oil tank in the hydraulic station， and once water is mixed in the hydraulic station， the damage to the hydraulic system is very large. Therefore， it will simply form pipeline corrosion and water vaporization， which will cause adverse effects or results. Therefore， it is necessary to prevent this to ensure the normal operation of the hydraulic station and its service life.

After the inspection， the lift manufacturer reminds you that you should use a compressed air machine to dry all the electrical connection parts inside the head bin to prevent water from accumulating on the electrical connection parts and causing erosion.