LimestoneFully automatic elevator electricSurface corrosion treated

What are the advantages of installing the rail-type elevator and cargo elevator? The advantages of civil engineering are easy to install: there is no need for a machine room above the hoistway， and the top floor can be installed more than meters high. The machine room can be set within the radius of meters of the shaft， and the brick structure or brick-concrete structure hoistway is sufficient.

6The boxes and distribution boxes are usually kept clean， and dust on the electrical equipment should be cleaned quickly.

bLimestoneThe load causes the motor to overheat， and the load causes the motor to overheat are as follows: motor overload operation. When the equipment is not matched and the load power of the motor is greater than the rated power of the motor， the motor will be overloaded for a long time，Elevator manufacturer which will cause overheating of the motor. When repairing the overheated motor，HoustonFixed scissor liftThe foundation of the industry it is necessary to find out whether the load power is consistent with the motor power to prevent blind and purposeless disassembly.

In recent years， there are no more than three factors that lead to the occurrence of domestic elevator accidents in mobile elevator manufacturers. They are human operation errors， which are purely caused by the lack of relevant equipment operators. The second is the simple hoist that has been screened in China and is not allowed to be used. This kind of hoist is potentially dangerous. And because the country has banned the production of this kind of simple hoist， the existing equipment is often aging， which is more prone to accidents. The third is that the quality of production is not up to standard， leading to severe social security incidents.

RAzerbaijanOperation cost advantage: low failure rate. Due to the use of advanced hydraulic system and good methods， the elevator operation failure rate can be reduced to a minimum. Low power consumption: when the hydraulic elevator goes down， it is driven by the pressure generated by its own weight， tighten the connector and take out the oil filter. After cleaning，Elevator manufacturer clean it with compressed air， and then put it back into the oil tank and connect the pipeline.

Anti-corrosion measures for the body of aerial work vehicles Pay attention to small scratches. The paint surface of aerial work vehicles often corrodes. In addition to the common collisions， scratches， and small rocks on the driving tires， there can also be a paint peeling point， and there will be a small rust after a long time. Because most of these scars are small and easy to ignore. Therefore， regularly check the body， go to a professional beauty shop for processing.

Make the foundation according to the foundation plan， pay attention to the alignment， leveling and alignment，Elevator manufacturer and ensure the level of the foundation and various use requirements.

gWith the development of social science and technology， aluminum alloy elevators are used more and more widely. Hydraulic lifting machinery is indispensable to architecture，HoustonFixed scissor liftThe foundation of the industry civil engineering and peoples daily life. Many businesses seize this opportunity to invest in and build factories. Lifting machinery companies are standing like bamboo shoots in major industrial cities but the lifting machinery industry is still hot and in short supply， Now the rapid development of society has driven the development of the entire industry and peoples needs. However as can be seen from the side， as a buyer， how to choose a good lifting machine has become an important topic today.

JNovice operation: because novices do not know much about mobile elevators and other aerial work platforms， or do not understand the operation mode， it is easy to cause equipment failure due to operation errors. Operators in this field need to learn patiently and can only operate after training.

RTotal quality assuranceJust like the failure of the traveling part of the lifting platform， the operator must master the common sense of equipment maintenance failure， so that when the failure occurs，Lift_ Hydraulic elevator_ Hydraulic lift_ Hydraulic lifting platform - lift manufacturer it will not appear too flustered. Generally speaking， the axle box bearing is burnt， the traction motor bearing is burnt， the tyre is loose， and the crack is damaged. Lets share the solution with you.

sBDouble-column aluminum alloy lifting platform is beautiful and generous in design. It is made of high-strength aluminum alloy material， with large bearing capacity. The height is generally -m， and the load is kg-kg. Large table design allows one or two people to work at the same time.

Avoid humidity， especially during storage. Store in a cool and dry place， and avoid rain and snow during work.

How do lift manufacturers maintain and maintain construction lifts? In order to accurately implement the equipment maintenance system， a mechanical management responsibility system must be established; Maintenance procedures for different models must be formulated; The corresponding maintenance organization must be implemented; The relationship between maintenance and production must be properly handled to ensure that it does not affect production and equipment maintenance.

Energy costszThe pressure of the lifting platform is very important. When lifting the general cargo， the pressure of the lifting platform will test the weight of the cargo. If the general lifting platform is overloaded， it will prompt， which plays a protective role. So now the lifting platform is equipped with a pressure gauge. Hydraulic machinery should remind you of the following points: The use of small lifting platforms depends on the pressure. Their load capacity is very poor， and their size is small. When using the lifting platform， we must pay attention to the use of the lifting platform. If overload is used， the structure of the lifting platform will be damaged. We have said many times before when using it.

PLiterstrength; Half of the elevator cables are used for extension. High-rise elevators can reach more than meters， and the dead weight of the -meter cable is nearly kilograms， so the cable must have sufficient tensile strength. At present， there are self-supporting flat composite elevator monitoring special cables on the market. This kind of cable combines video coaxial cable， the tension of the whole cable is borne by the steel wire rope data cable and steel strand to form a flat ribbon cable. In this way， and the tensile strength is very good. It will not break the signal cable due to gravity during elevator operation.

The smooth and hydraulic oil of the slowing down box， gearbox， external gear and other departments shall comply with the requirements in the smooth table.

tLimestoneAlways check all wires and cables for damage.

qLThe hydraulic torque converter and compensation system of mobile elevator are defective， such as the hydraulic torque converter is weak， the power shift fails， the oil temperature is too high， the hydraulic torque converter is weak， the hydraulic oil quantity is insufficient， the pressure is not adjusted properly， the back pressure is insufficient， the torque converter oil quality is checked (whether the hydraulic transmission oil is misused)， the amount is used， the torque converter pressure regulating valve， the back pressure valve and the set pressure value of the power shift fail， the quick-return valve， the pressure reducing valve， the power transmission valve The reversing valve is jammed and internally leaked. The oil pollution is serious. Check the cause of valve jamming and make corresponding elimination， filter or replace the hydraulic oil. If the oil temperature rises too high， check whether the cooler is defective. Check the hydraulic oil quality. The brand hydraulic boarding bridge is also known as the hydraulic loading and unloading platform. It can realize the rapid loading and unloading of the goods. It is simple in structure design， flexible and convenient in use high in efficiency， and is widely usedPopularize in the market.

Purpose of manual hydraulic platform: the manual hydraulic handling platform is novel in design， reasonable in structure and convenient in use. It is applicable to the loading， unloading， handling and stacking of drums in factories workshops， warehouses and oil depots. It is especially suitable for the use of chemical and food workshops for pouring or batching， and can load and unload heavy goods on trucks and stacking， and cooperate with the operation of hydraulic drum trucks， which can greatly improve the work efficiency and reduce the labor intensity， and can also be modified for loading and unloading and lifting heavy goods. It is a new and ideal multi-purpose lifting and unloading machinery.