MerinacFully automatic electric elevatorIndustry management

The middle rotating shaft of the support rod of the hydraulic lifting platform is inconsistent， which causes the lifting platform to be unable to work normally， and the table has tilted. Please carefully check that the general shear-type aerial work platform was put into the market without strict tilt detection before leaving the factory， resulting in many accidents. For tilt detection， the majority of small enterprises do not pay much attention to the detection of this link， This is why there are so many lifting equipment with this problem. The problems of oil cylinder and power unit system are often the problems of insufficient power and unqualified oil cylinder quality，Products which are also very important for the enterprise itself.

1For lifting platforms in some sites，GvogovFixed hydraulic elevatorIt is best to maintain a biased operation mentality protective barriers are generally added on the platform. Since the lifting platform is a special equipment， the National Quality Inspection Bureau is very strict with this inspection. As long as it is considered that there are potential safety hazards， the lifting platform should be removed. So when the salesperson asks you whether to add guardrails， do not blindly refuse， and consider whether it is necessary according to the site of use. In addition， the production， installation and maintenance can only be carried out with two kinds of certificates， namely， the Special Equipment Manufacturing License of the Peoples Republic of China and the Special Equipment Installation，Products when purchasing， which can also be customized according to user requirements， and the load can reach tons.

It is strictly forbidden to connect the lifting platform motor to the wrong power supply. It must be v or v voltage to do a good job of daily cleaning， and timely clean the dust and debris on the motor.

EDembidoloIf the water has entered the motor of the elevator， the motor should be disassembled so that the water can evaporate quickly. This is a very fast dehumidification method in summer.

TsAccording to the development law of the elevator， there will be a rebound if there is a trough， and if there is a downturn， the industry may disappear; Secondly， the policy is the booster of the industrys recovery， which increases the infrastructure construction，Products which provides a great opportunity for the industry; After that is“ The Belt and Road” This is undoubtedly another opportunity for the industry.

The contact surface of each departments brush shall be kept clean， and the brush pressure shall be adjusted to make the contact area not less than %

Thermal spraying of aluminum oxide after sand blasting. Applicable to all media except water and glycol; Spraying antirust primer can significantly reduce the corrosion of steel by adding antirust primer to the paint during spraying.

aOutriggers: mechanical outriggers，GvogovFixed hydraulic elevatorIt is best to maintain a biased operation mentality hydraulic outriggers， ordinary hand-operated outriggers， the small oil cylinder starts to work and stretches out the loose-leaf tongue. All the equipment plates are effectively welded with high quality checkered steel plates and profiles， with long service life.

VQuotation sheetRegularly add lubricating oil to maintain the lift: during the use of the lift， the friction between various components is also relatively large due to the heavy load， especially the lift chain and the lift pivot pin. It is necessary to ensure that the appropriate amount of lubricating oil is added before each use to ensure that the operation is flexible and not blocked. If the elevator is running， once“ appears; Squeak” It can be basically concluded that the friction noise is due to the lack of lubricating oil in the elevator. It is necessary to stop working immediately and find out the reason. It is easy to cause unpredictable hidden dangers. Point summary: it is not allowed to add lubricating oil regularly to maintain the elevator.

sBThe oil cylinder seal is not replaced in the oil cylinder of the boarding bridge manufacturer. The lifting table does not lower. The lowering valve fails. When the lowering button is pressed， check whether the lowering valve is powered on. If there is no electricity，Lift_ Hydraulic elevator_ Hydraulic lift_ Hydraulic lifting platform - lift manufacturer try to eliminate it; If there is power， remove the fault of the lowering valve itself， or replace the lowering valve. The lowering valve should be kept clean and lubricated.

The anti-rust work of aerial work vehicles is generally something that needs attention when aerial work vehicles have not been used for a long time. How should we protect the body of aerial work vehicles from corrosion? In fact， it is very simple to go to the maintenance station for anti-corrosion， as long as our car owners can use some materials they can find and pay attention to the driving habits to ensure that the aerial work vehicle does not rust. Here are some points for reference.

How to properly maintain the elevator and regularly replace the elevator hydraulic oil: The hydraulic oil used by the elevator is divided into winter and summer， which is something that many elevator customers do not pay attention to. They often inject hydraulic oil once and ignore it for a long time， and often do not realize it until it causes the elevator hydraulic oil cylinder to work abnormally.

reformcCheck before use Carefully check the grounding wire safety device， buffer spring， etc. before use. Ensure a safe use environment.

WThe lifting platform price elevator and lifting platform are applied to the airport terminal， aircraft emergency repair， stations， docks， shopping malls， stadiums residential properties， factories and mining workshops and other large-scale high-altitude continuous operations. Some products have the function of active walking. They can walk fast and slowly under different operating conditions. Only one person can operate the machine in the air to finish up and down， travel， retreat， turn and other actions. When the machine is in the stop state， the wheels are always in the braking state， and can firmly brake on a degree slope. Large-diameter and ultra-wide high-quality rubber wheels enable users to get useful maintenance on the ground and increase braking friction.

When filling hydraulic oil， we can extend the oil cylinder to the high position for filling. When filling， the lifting platform should not exceed the high position， and then retract the oil cylinder to the low position. Check whether the hydraulic oil level is lower than the low position， and keep it between the two.

lMerinacThe hydraulic lifting stage roller， ball， turntable and other tables can be arbitrarily configured to meet the requirements of different working conditions.

wKHow to prolong the service life of hydraulic lifting platform? In order to prolong the service life of such machinery and equipment it is necessary to regularly repair and maintain the equipment during normal use. For example， there are various switch devices in the machinery and equipment. During use， it is necessary to regularly check whether these switches can be used normally and whether the contact points of the switches are good. There will be an electric box and distribution box inside the elevator. Dust is easy to accumulate outside these equipment. If too much dust is accumulated， it may cause corrosion outside the electric box. Therefore， the dust outside the various boxes should be removed regularly during use. Generally， which causes the lifting platform to be unable to work normally， the platform has been seriously damaged， and the table has tilted. Please carefully check that the general shear-type aerial work platform was put into the market without strict tilt detection before leaving the factory， resulting in many accidents. For tilt detection， the majority of small enterprises do not pay much attention to the detection of this link， This is why there are so many lifting equipment with this problem. The problems of oil cylinder and power unit system are often the problems of insufficient power and unqualified oil cylinder quality， which are also very important for the enterprise itself.